Customer Reviews
Shopping Cart: 0 Item(s) Totaling: $0.00

Mug Wrap - 11 Oz.

Mug Wrap - 11 Oz.

11 oz Silicone Sublimation Mug Wrap with easy to close and quick release clamp fastener. This product makes it effortless to produce an imprinted mug with a full picture that can reach all the way around. At this cost efficient price, it makes the perfect tool if you are just venturing over to mug sublimation or transitioning from a mug press.


Use with our 3D sublimation vacuum heat press only!


Brand:
Pro World
Finish:
Textured
Substrate:
Silicone
Size:
11 Oz.
Item #:
SB-S-024
Rate or review to get 200 PW Reward Points

Availability: In stock

Your Price: $11.95

or Clear Form
  • Details
  • Instructions
  • Videos
  • Reviews
  • Product Details

  • Application Instructions

    1. Turn the 3D Vacuum Heat press on.
    2. Set the heating button so both the top and bottom heating lights are on. (2 red lights will be showing)
    3. Set the Temperature to 392 degrees F (200 degrees C) and time to 500 seconds. Add 2 minutes (120 seconds) for each additional mug placed in the Vacuum Press.
    4. Print a mirror image onto Texprint Paper.
    5. Trim the edges of the image and wrap around mug.
    6. Attach the image to mug using transfer release tape.
    7. Wrap mug with mug wrap.
    8. Place upside down within the heat press.
    9. Press vacuum button
    10. Press the time button
    11. Remove immediately once finished and peel hot. Use caution as mug will be very hot.
    12. Dip mug into warm water to cool and end the sublimation process
    Click Here For Video Instructions

    Application Instructions

    1. Turn the 3D Vacuum Heat press on.
    2. Set the heating button so both the top and bottom heating lights are on.
    3. Set the Temperature to 392 degrees F (200 degrees C) and time to 8.5 minutes (510 seconds). Add 2 minutes (120 seconds) for each additional mug placed in the Vacuum Press.
    4. Print a mirror image onto Texprint Paper.
    5. Trim the edges of the image and wrap around mug.
    6. Attach the image to mug using transfer release tape.
    7. Wrap mug with mug wrap.
    8. Place the mug on its side on the wire rack within the press.
    9. Press vacuum button
    10. Press the time button
    11. At approximately 5 minutes, flip mug over so the opposite side is facing up in the vacuum press. Close the vacuum press and continue with the remaining time.
    12. Remove immediately once finished and peel hot. Use caution as mug will be very hot.
    13. Dip mug into warm water to cool and end the sublimation process
    Click Here For Video Instructions
  • How To Sublimate A Ceramic Mug Using A Convection Oven And A Mug Wrap
    Printing Mugs with a 3D Vacuum Press
  • Customer Reviews

    Rate or review to get 200 PW Reward Points(What is this?)
    Mug Wrap Review by Lisa Austin
    Quality
    Price
    Value
    Things things are GREAT. At first, squeezing together I thought I was going to break the mug it was so tight! but then I realized...it's supposed to be that tight! These things work great! I can't believe I waited so long to join the sublimation world!! (Posted on 8/28/17)
    Impartial to This Review by Miranda
    Quality
    Price
    Value
    The quality of this item is really great. However, it is hard to get on and off. I always end up hitting my hand with the clips. (Posted on 7/31/17)
    Works Well Review by Pat
    Quality
    Price
    Value
    Once you figure out how to put these on, they work great. There should be a video showing you how to use these! (Posted on 7/15/17)
    Show More